How We Built It Part 1: Resources, Design, First Part of Install (Windows, fan, insulation, floor, and leak fix)


Let me just start by saying that we never would have completed this project without the help of many folks from various resources. I'm not affiliated with any of these companies and am getting no compensation in any form to mention them. They were all standout and deserve to be mentioned. 

The top ones we used were:

1. Ram Promaster Forum (www.promasterforum.com)

From the design phase, build phase, and troubleshooting, this group of people was invaluable.

2. Bogart Engineering (http://www.bogartengineering.com/)

Kedar, the owner and engineer, was consistently knowledgeable, helpful, and professional. His input was critical for the electrical build, which was the most intimidating part to me. His electrical components are top-notch and working flawlessly.

3. Explorist Life (explorist.life)

Nate's how-to video series and diagrams are extremely well done and informative. I basically learned how to become an amateur electrician by utilizing his content.

4. Unaka Gear Company (unakagearco.com)

Dan and Eric installed our solar panels, the only part of our build that we hired out. They patiently worked with me to design my layout prior to the install. Also very helpful with electrical questions and components. I purchased most of my electrical from them. The excellent free advice was a nice bonus!

So, let's get on with it! 

DESIGNING THE LAYOUT

We spent literally months on the design. We drew on our own experience owning an RV, and then renting a camper van a couple of times to try it out. We consulted the Promaster Forum and other blogs extensively to glean knowledge and insight from others. We also used CAD: cardboard aided design! After building a bed prototype of plywood, we then constructed crude cabinets from cardboard to get a feel for the space when built out.

We ultimately decided to go with the bed right behind the front seating area. We wanted an open feel in the van, and the bed conversion to make a sofa during the day was key for that along with a wider aisle (30+ inches). We also like using the back doors more than the slider. Traveling with our two 40+ pound dogs, we wanted a secure place for them to be when the van was moving, when they were left alone in the van, and also at night so we wouldn't be stepping on them. So their kennel is under a portion of the bed. By placing the bed in the front, we knew we were sacrificing the obvious advantage of swivel seats, along with being able to step through from cab to the rear of the van. But in the end were ok with that. 

Once the bed position was decided, we could then position the rest (cabinets, windows, etc.). The picture shows a small bench at the passenger rear. During the build out process, we elongated this to fit two people, and are really happy with the finished product (more on that later).



WINDOWS AND FAN INSTALLATION

First we did all of our "cuts" in the sheet metal. We chose Motion Windows for the back (t-sliders on both sides), and passenger side (two side door t-sliders, one in the slider and one immediately behind). We chose an Artic Tern 450x1100 for the driver side towards the rear of the van. The Arctic Tern with a top hinge can stay open in the rain, so we wanted at least one window with this option. We chose the Maxx Air Max Fan Deluxe 7500, installed over the bed area (towards the front of the van for our build). We installed the fan using the vent fan adaptor and framing strips from DIY van- I found these very helpful, especially the adaptor for the roof.























At this point, we weighed the van: 5,000 pounds.

SOLAR PANELS AND ROOF RACK

Next was the installation of the roof-top solar panels. We first chose the brackets from Unaka Gear Company. Because they were local to our area and seemed very qualified, we hired them to install the rack system and solar panels. We chose two (2) 200-watt monocrystalline solar panels from Newpoa. The Unaka rack system utilizes angled brackets that clamp to the factory t-studs already on the roof. Unaka routed the cables in through the rear camera housing. So, no new holes were drilled into the roof for this system, which I really liked. I had Unaka install the 8020 rack as far to the rear of the van roof as possible, and also add a 1/4 round piece of 8020 to the front of the rack. Based on an MPG test conducted before and after the rack and panels were installed, I suffered no MPG penalty. I was really happy with that, along with the low-profile look.











INSULATION AND FLOOR

We then started on the wall and ceiling insulation, as follows:

Ceiling: 1 inch polyiso

Walls: 2 inches polyiso (1 inch pieces stacked).

All poly was double foil faced. We used about 5 sheets total. We applied Great Stuff Gaps N Cracks (using a Pro Gun) to adhere the panels. To allow for drainage of any condensation, we oriented the Great Stuff along the length of the van for the ceiling, and vertically on the walls. The panels were stabilized during curing of the Great Stuff using "bendy sticks" (1x2s). We great-stuffed the cut edges of all the panels (this was very tedious). We used Noico on the wheel wells and the slider (note: the best installation tool for the Noico: a plastic kitchen scraper,). Also added 3M Thinsulate SM600L on top of the  Noico, under the headliner, and in the doors and some cavities.

We purchased our van used, and in it's first life it was used as a bakery delivery van. So the first part of the job was cleaning all the walls and floor very well, removing old glue and insulation, and applying fresh paint and primer as needed. 































Floor sandwich (top to bottom):

Black Promaster cargo mat

3/4 inch plywood (3 coats polyeurathane)

1 inch 25psi Kingspan Greenguard XPS (3 sheets, from local Lowes hardware)

We used hanger bolts through the tie-down holes to mark the floor insulation and plywood for drilling out the holes.

CLEARANCE LIGHTS LEAK

I next discovered that the clearance lights were leaking. These are the amber lights mounted on the front of the van, near the roof. I purchased a set of new lamp clips from Steve White parts, and spent a couple of hours on top of the van replacing all the clips and adding Dicor (non-leveling non-sag) around the outside of each light as a precaution. Leaks fixed!



















Comments